Before using the device, read the operating manual carefully, in particular the safety instructions.Excell A20118 Manual Online: Pressure Washer Operating Features. It contains important information on start-up and handling. General information General information Reading and storing the operating manual This user manual accompanies this 2.2 kW high pressure washer (referred to below only as washer).9 Connecting to a network. 4 Installation configurations. 3 Unit installation checklist. Generac 4200 PSI Pressure Washer Model 6565.Husqvarna 2000 PSI Electric Powered Pressure Washer 2000 Max PSI / 1.2 Max GPM 3 Quick-Connect Spray Tips Operates vertically or horizontally 7 Solid Wheels Tubular Steel Frame2 HYDRIM C6w G4 Installation Instructions Environmental requirements.All other trademarks referred to in this manual are the property of their respective owners. BRAVO, HIP, and SysTM are a trademarks of SciCan Ltd. 2 HYDRIM and STATIM are registered trademarks of SciCan Ltd.
Inventek Power Washer Manual This UserWater flows through an unloader and output pipe on the pump, and then through a hose to the spray gun. The pressure washer pump consists of three plungers or pistons that operate in a similar manner to a piston in an engine. 70 Technology Drive Canonsburg, PA 537 USA Phone: Fax: Toll free: SciCan Medtech Alpenstrasse 6 CH-6300 ZUG SWITZERLAND Phone: +4 (0) Fax: +4 (0)Electric pressure washers use a motor to drive the pump while most gas-powered washers will use a 4-cycle engine. Please review these factors, before installation and ensure the location is suitable. There are several factors that may affect the performance of your HYDRIM. Installation should only proceed after the satisfactory completion of the pre installation documentation. 3 HYDRIM C6w G4 Installation Instructions NOTE: The HYDRIM C6w G4 unit should only be installed by a trained, SciCan approved technician. Do not move the HYDRIM C6w G4 into place by maneuvering the open wash chamber door. Spacing The vents and openings on the HYDRIM should remain uncovered and unobstructed. The recommended operating temperatures are +5 to +40 C with humidity of 80% for temperatures up to 3 C and 50% for temperatures up to 40 C. We recommend that the unit be kept away from potential sources of interference. While the unit does not emit any radiation, it may itself be affected by other equipment which does. Electromagnetic Environment The HYDRIM has been tested and meets applicable standards for electromagnetic emissions. Never install and operate the unit on a sloped surface. Work Surface The HYDRIM should be placed on a flat, level, water-resistant surface. Venting The HYDRIM should be operated in a clean, dust free environment. Cleaning chemicals may be incorporated into the spray if desired.4 HYDRIM C6w G4 Installation Instructions Unit installation checklist NOTE: Refer to Operator s manual during installation for operating the machine. Instructions for Installation/Set-up, Operation, Maintenance, & Storage This pressure washer produces cold-water high-pressure spray. WARNING: NEVER LOCATE THE HYDRIM WITH THE ELECTRICAL OUTLET RECEPTACLE BEHIND THE MACHINE! Owner’s Manual Pressure Washer: Machine that cleans dirty surfaces with high pressure water. If using a surge suppressor power bar, plug in one HYDRIM only. Avoid multiple outlet receptacles. Cabinet / Sterilization Center 5 HYDRIM C6w G4 Installation Instructions Option 2. The configuration options are: Option. Unit installation Installation configurations The HYDRIM C6w G4 may be installed under-bench or free standing dependent on space and service availability. Please ensure cleaning solution has been separately provided prior to installation. This may cause the door to become misaligned and can cause leakage. 6 HYDRIM C6w G4 Installation Instructions Set up unit as follows: Unpack unit and remove all restraining ties Locate unit in approximate position NOTE - Do not move the HYDRIM C6w G4 into place by maneuvering the open wash chamber door. The free movement of air to this intake is important and failure to provide the required space may cause overheating of the dryer motor and/or compromise drying efficiency. NOTE 3 - The drying system has a filtered air intake. NOTE - If hot water/ro feed is not available then it must be possible to attach a Y fitting to the cold water feed valve so that both machine pipes can be connected to the cold supply. Make sure that the inlet valves are free of debris (5 & 6). The end of the hose with the gasket and the screen should attach to the water supply connector. The connector with the elbow should be attached to the drain outlet (3) on the back of the HYDRIM unit. NOTE 3 Waste connection should be adjacent to the machine and not behind it. Under no circumstances should any other equipment share the standpipe. This must be a dedicated standpipe. If the HYDRIM is not close to a sink unit and a P trap cannot be used, then a standpipe with U bend fitting can be used. Wherever possible, if the HYDRIM is located close to a sink unit, then this method should be used. Get an ios emulator on macTo level the unit, follow these steps. Level machine in final position with adjustable legs For the unit to function properly, it will need to be correctly leveled. A floor drain is acceptable (check local codes). If the hose is connected directly to the drain line, fittings and adapters should not reduce water flow. The drain hose can be attached to existing drain lines using a 3.5 cm or larger standpipe/ P-trap combination. A dedicated hard wired 2A supply can also be used. OR Standard domestic outlet Voltage: VAC ☐%, single-phase, 60 Hz, 2A Located within.50 metres maximum Supply location (see notes below) Power cord routing (see note below) NOTE The HYDRIM C6w G4 is supplied with a domestic fused plug as standard. Use a level as a guide Connect machine to power supply Electrical supply requirements: Dedicated 2A independent supply (see Note below). Dissolved solids in the water can cause stains, spots, and corrosion on instruments and the internal parts of the HYDRIM. 9 HYDRIM C6w G4 Installation Instructions Checking Water Quality The quality of the water being used in the HYDRIM to clean the medical instruments is very critical to achieving satisfying cleaning results and to protecting the instruments and the internal parts of the HYDRIM from deterioration. The cable should be routed away from the back panel and hot water inlet hose. NOTE 3 - Power supply outlet should be adjacent to the machine and not behind it.
0 Comments
Leave a Reply. |
AuthorVaibhav ArchivesCategories |